FAQs

How can I collect Pressure and Temperature data in the same software?

Setting the data collection window with a map has always been the first configuration step in I-Scan. If you've used it before, this will be very familiar. By selecting a Temperature map, the software knows to enable temperature features for that window. The software will also enable the Temperature legend which uses a unique color scale from the pressure map to ease the analysis.

 

Link to this FAQ

What is the data capture rate of the temperature mapping system?

The Evolution handle used in the I-Scan temperature mapping system can capture data on the sensor at up to 100 Hz.

 

Link to this FAQ

Can I do a one-point calibration with ambient temperature?

No, the slope of the temperature sensor’s calibration curve does not run through zero.  Two points are required to calibrate the sensor.  If a single point calibration is performed the calibration point will be saved in the system, but no calibration will be applied to the sensor.

 

Link to this FAQ

Can I take measurements with uncalibrated raw temperature data?

No, the temperature sensor does not provide useful information without a calibration.  Uncalibrated data can be collected for calibration purposes. Frame calibration is a useful method for calibrating this system.

 

Link to this FAQ

Do I need to equilibrate the temperature sensor?

No, the calibration process also equilibrates the T800 temperature sensor

Link to this FAQ

Can I calibrate the T800 temperature mapping sensor with a heating chamber?

Yes you can use a heating chamber, but using a laboratory grade hot plate is faster and more precise. 

Link to this FAQ

Can Tekscan sensors be cut or trimmed?

Question: Can Tekscan sensors be cut or trimmed?

Answer: Yes, some of our sensors can be cut or trimmed to smaller sizes or shapes, or even punctured for secure placement. The model 4205 (pictured), model 7800 pressure sensor and T800 temperature sensor are designed to be sized for custom embedding in battery placements or other tight spots.

image-20240820133832-1Tips for trimming:

The rows and columns are connected through silver dots and traces on the surface of the sensor. If you trim the sensor, a row or column will remain active so long as the silver dot and silver connecting trace remain intact and connected to the handle.

Based on this photo, you can trim up to 15 rows from the distal end of the sensor before you reach the column trace connections. And you can trim up to 5 columns from either side before you reach the silver connections to the rows.

Consult with a Tekscan engineer if you aren't sure if your sensor is trimmable or how to do it. Cutting through the sensing element will short the sensor! 


---
The ability to trim for shoe size is one of the most important advantages of our in-shoe F-Scan™GO sensor, which can be trimmed to fit any shoe size up to a men’s size 14.

Tips for trimming the F-Scan GO sensor can be found in the manual, or HERE. 

Link to this FAQ

What sizes are sensors available in?

Question: What sizes are sensors available in?

Answer: We have sensors in many shapes and sizes. Please refer to one of our sensor catalogs to see diagrams of our standard sensors. Contact Tekscan for the sensor that would best fit your application. Custom sensors are also available.

Link to this FAQ

What is the temperature range for sensor use?

Question: What is the temperature range for sensor use?

Answer: Standard Tekscan sensors are specified to operate in a temperature range from -40 ºF to 140 ºF (-40 ºC to 60 ºC). If the sensor is used at a temperature different than the calibration temperature, there will be a temperature effect.

The operating temperature range of the Handle is 32 °F to 122 °F (0 °C to 50 °C). Thus, if the application involves extremes of temperature, the Handle should be insulated or otherwise protected from the extremes of high temperature.

Many sensors can be produced with high temperature ink and substrate for use over a temperature range from -40 ºF to 400 ºF (-40 ºC to 204 ºC). The appropriate sensor for prospective high temperature applications is individually evaluated, and quoted.

We do also have High Temperature model sensors; they are specified to operate in a temperature range from -40 ºF to 400 ºF (-40 ºC to 204 ºC). Calibration would be affected when the temperature goes beyond this specified range. Keep in mind that we do not recommend the use of the ELF system handle with our High Temperature model sensors, and if you do intend to use it with the sensors, a waiver would need to be signed.

Link to this FAQ

Do I need an Instron device to calibrate my ELF system?

Question: Do I need an Instron device to calibrate my ELF or WELF?

Answer: No! You can use dead weights and that will work fine. The video calibration tutorial uses one, but it's not necessary.

 

Link to this FAQ