Have questions?  Contact Us

A502 Sensor

FlexiForce A502 Sensor

Large, square, standard sensor, ideal for OEM integration.  Available direct from Tekscan (below) or at Digikey and Mouser.

Download Datasheet

FlexiForce A502 Sensor
$222.53

Description

FlexiForce™ A502 Sensor

Digikey Mouser

A502 sensors are square standard sensors with a 2-pin male connector. They have a force range of 0-222 N (0-50 lb), specified with Tekscan electronics. The model is linear through a much lower range of 0-22N (0-5 lb), and is capable of measuring loads up to 44,482 N (10,000 lb).*

The dynamic range of this versatile force sensor can be modified by changing the drive voltage and adjusting the resistance of the feedback resistor (see "How to Adjust the Force Range" within the Electronics tab on the left).

Volume discounts icon

Typical performance

Force versus Resistance table

Specifications & Performance

Sensor Thickness: 0.203 mm (0.008 in.)
Force Sensor Length: 81.3 mm
Sensing Size (Diameter/Width):  50.8 mm
Standard Force:  222 N
Temperature Range (Low): -40 °C
Temperature Range (High):  60 °C
Connector: 2-pin Male Square Pin
Substrate: Polyester
Pin Spacing: 2.54 mm (0.1 in.)
Notes:  Tekscan's largest standard FlexiForce sensor

Typical Performance

Linearity (Error): < ±3% of Full Scale (Line drawn from 0 to 50% load)
Repeatability: < ±2.5% (Conditioned Sensor, 80% of Full Force Applied)
Hysteresis: < 4.5 % of Full Scale (Conditioned Sensor, 80% of Full Force Applied)
Drift: <5% / logarithmic time (Constant Load of 111 N (25 lb))
Response Time: < 5 µsec (Time required for the sensor to respond to an input force; Impact load - recorded on Oscilloscope)
Operating Temperature:  -40°C - 60°C (-40°F - 140°F)

Durability:

≥ 3 million actuations (Perpendicular load, room temperature, 22 N (5 lb))

Temperature Sensitivity:

0.36%/°C (± 0.2%/°F) (Conductive heating)

All data above was collected utilizing an Op Amp Circuit. If your application cannot allow an Op Amp Circuit, consult the FlexiForce Integration Guide, or contact a FlexiForce Applications Engineer.

Electronics

Tekscan Recommends Using an Op Amp Circuit

If your application cannot allow an Op Amp Circuit, consult the FlexiForce Integration Guide, or contact a FlexiForce Applications Engineer. If you prefer to build your own electronics, we recommend using a circuit similar to the diagram below. This will provide linear data, making it easier to calibrate the sensor.

A502 circuit diagram

How to Adjust the Force Range:

*In order to measure higher forces, apply a lower drive voltage (-0.5 V, -0.25 V, etc.) and reduce the resistance of the feedback resistor (1kΩ min.) To measure lower forces, apply a higher drive voltage and increase the resistance of the feedback resistor.

Related Products

FlexiForce Sensor Characterization Kit

FlexiForce Sensor Characterization Kit

The FlexiForce™ Sensor Characterization Kit is a time-saving, affordable tool enabling engineers and designers to understand how FlexiForce sensors perform in a controlled loading environment.

FlexiForce Prototyping Kit

FlexiForce Prototyping Kit

The FlexiForce™ Prototyping Kit allows you to efficiently progress your FlexiForce-embedded design through advanced integration phases. 

Note: The FlexiForce Prototyping Kit includes an open-source software program designed specifically to help with the sensor integration process. Some code programming experience is necessary. 

New and improved replacement for the OEM Development Kit.

Available direct from Tekscan or at Mouser.com.

FlexiForce Quickstart Board

FlexiForce Quickstart Board

The FlexiForce Quickstart Board is a finished single voltage source circuit which can be quickly dropped into a prototype or easily designed into a product to obtain force measurements. Available direct from Tekscan or at mouser.com.

FlexiForce Load Concentrators

FlexiForce Load Concentrators

Optimize FlexiForce sensor linearity and repeatability with these delrin load concentrators, or "pucks." Available direct from Tekscan (below) or at Digikey and Mouser.

FlexiForce Analog Circuit Modules

FlexiForce Analog Circuit Modules

Interchangeable circuit modules for use with the FlexiForce Sensor Characterization Kit, the FlexiForce Prototyping Kit, or your own electronics.