Knowledge Base

 

Search the Knowledge Base by product or keyword to find solutions to issues with hardware and software.


Search KB

Enter keywords or phrases

Filter KB

Related Product

There are 95 results.

Support
F-Scan Mobile can only upload one movie
My software does not recognize my USB Handle. I get the error: No Handles Found
Fn+F7 keys cannot be used to switch display from the laptop screen to the projector when Hardware Acceleration is disabled on an IBM Thinkpad laptop
Force/Pressure graph cannot be displayed or is transparent when using a projector
Periodic saturated (red) frames during recordings with Tekscan PCI electronics and computers with Hyperthreading enabled
How does the level of accuracy change as curvature of surfaces increases?
No Handles Found... with Parallel electronics
Error: You do not have a registered copy of F-Scan on your computer
How to convert .fsx movie files recorded in the Tekscan software into a standard movie format
What is the value named EQUFLAG?
Different values for the feedback resistor in the recommended FlexiForce circuit
Recommendations of adhesives for use with sensors
Are Tekscan sensors waterproof?
How to convert Resistance (Ohms) to Force (lbs)
Can I use FlexiForce sensors to measure dynamic loads?
Error: Operation must use an updateable query
Changed settings are not remembered after the software is closed
Video is out of synch with the Tekscan recording
Error: Failed to initialize the ELF device. No device was found
Error: This version of Windows Media Player is not supported on Microsoft Windows 2000
Steps to take in the event of a system crash
Movie freezes for a few seconds during playback
Why is Vcc of the op-amp -9 to +9?
What is the benefit of using an inverting op-amp circuit as opposed to other types?
Why the FlexiForce sample circuit uses op-amp MCP6004 as opposed to other commonly available ones -- such as LM741
Real-time data freezes for several seconds at each frame
Too few parameters. Expected 2
How to export and import EMG traces with BioPAK software
How to tell if my Sensor's sensitivity is suited to my application
Tekscan 32-bit Fsxview Executable has encountered a problem and needs to close
How can I extend the length of USB cables for Tekscan Handles?
Display of pressure is delayed
What is Tek WiFi (Wireless Capability)?
Where are the A & B lines in T-Scan 5.0 (T-Scan III)?
How to Export a patient's movies from one Tekscan application for viewing in another Tekscan application
Stance phases are not properly separated with lightweight subjects
Error message: "Old version of driver or driver cannot be found (tlw32vxd.vxd)"
The Real-time Status Bar reads ‘MISALIGNED!’ instead of ‘Sensor OK’
Communication problems with Wireless ELF
Error: Failed to initialize the Wireless ELF device. No device was found
How to show a continuous movie without having to continually push play
How to view pressure data ASCII files with the extension .asf
The ELF software starts without an error message, but the ELF handle is not recognized and the New recording button is inactive.
How to display percentages inside the arch (T-Scan III software)
How to improve Calibration accuracy and repeatability with ELF
How to calculate acceleration
How do I calibrate my FlexiForce Sensor?
My software does not recognize my Evolution Handle. I get the error: No Handles Found
Why are the stance phases in the Force/Time curves not starting at 0 kg (0 lbs)? Shouldn't the starting point be 0 kg (0 lbs)?
FlexiPot: Comparison of 3-pin vs 2-pin Termination
What sizes are sensors available in?
What is the minimum spatial resolution?
What are the sensors sampling rates?
How many tests/runs do sensors last for?
Can I customize a sensor’s size and/or pressure range?
Can your sensors be trimmed to a smaller size or shape?
Will my system work with all Tekscan sensors?
What is calibration?
Do sensors come calibrated?
Is calibration possible for dynamic loads?
What is equilibration?
How much can I overload a FlexiForce sensor without damaging it?
What is the lifetime of a FlexiForce sensor?
What materials/conditions could damage a FlexiForce sensor?
Can I fold a FlexiForce sensor?
Can I adhere a FlexiForce sensor to a surface?
How can I measure forces greater than 100 lbs?
What drive voltages can I apply to a FlexiForce sensor?
What is the maximum recommended current for a FlexiForce sensor?
What is the resistance range of a FlexiForce sensor?
How do I connect a FlexiForce sensor after it has been trimmed?
Why do you need to condition a FlexiForce sensor?
How much error is induced if a FlexiForce sensor is not conditioned?
What is the maximum period of not using a FlexiForce sensor before you have to recondition it?
Why do I need to calibrate a FlexiForce sensor?
Is “110% of the maximum load” what a FlexiForce sensor can handle?
What is a puck/shim and do I need to use it?
What material is best to use for a puck / shim?
What surface is best to use underneath a FlexiForce sensor?
How fast is the Prescale System's minimum measurable pressure application speed?
How fast does the developed color of Prescale fade and what is the best way to keep the measured Prescale from being deteriorated?
What are the specifications of Tekscan's sensors?
Can Tekscan sensors be cut or trimmed?
How do I clean Tekscan sensors?
How do I purchase additional sensors for my Tekscan system?
Can I purchase only Tekscan sensors?
Will my system work with all of Tekscan’s sensors?
Can I customize a Tekscan sensor?
FlexiForce User Manual: How do I use my FlexiForce Sensors?
Why do I need an excitation circuit to read force with FlexiForce A201 sensors?
How do I clean my T-Scan system components?
Can I Trim the FlexiForce sensor?
Does Tekscan software support local languages?
Error: "No More Available Handles" when opening a Real-Time Window
What is the temperature range for sensor use?
");